Sharpening auger blades

[ScreeminReelz]

Just thought I'd share a tip with those of you that have dremel tools and dull blades on the ol' auger. They make a blade sharpening guide that threads on so you can get a good, even edge along the blade. It works KILLER for sharpening auger blades! Mine works like brand new again and the blades were super dull before. Anybody else have the same success??

[goggleye57]

Where do you get them? I use my dremel to sharpen my saw chain and it is easy to get it really sharp quickly.

[ih772]

They have them at HD and were about $10 the last time I saw them.

[goggleye57]

Sorry- I'm not familiar with HD?

[ih772]

Home Depot

[goggleye57]

Thanks! I'll go and see if they have them here

[ESOX]

Just like sharpening a good wood chisel or plane blade, the flatter you can get the back, the sharper and more efficient the cutting edge will be, because the edge will be on the same plane all the way across. They might look flat, but they really aren't, as will be aparrent when you start lapping them. Even top quality tools need a bit of work before they are really ready for use, and auger blades can require quite a bit of work, but it is well worth it.

Use a piece of glass and use spray contact adhesive to attach a piece of fine emery cloth to the glass. (I use a granite inspection plate, but glass works just fine for ocassional use.) Work the back of the blade on the cloth untill the surface is straight all the way across. You can use progressively finer grits untill you get a mirror like polish on the back if you desire. I'll even finish my chisels with chrome polish on a piece of cardboard, but that might be going just a tad overboard for an auger blade. Then put the bevel on the top side of the blade. You will be suprised at how much easier your blades cut when the back of them is dead flat.

[Full Choke]

esox
Could not of said it better myself!
Steve R

[DaveW731]

Will the Dremel approach work with Lazer blades? I have done OK with a hand sharpening tool that allows me to follow the curve of the blade, but if the Dremel would work, I think it may be faster.

[gamalot]

I used one of the blue auger sharpeners available at the bait shop. They should be called "DULLERS"!
I ended up making a speed run to the bait shop to buy new blades for the laser, OUCH!
I was able to repair the damage as stated above with the emery attached to glass just like I do my plane blades.

The wife was really thrilled with me! While at the shop getting new blades for the laser, I found this neat little gadget called a Strikemaster Mag 2000. $300 later I was a star at home!
In keeping with the motto by which I live, "It is much easier to ask for forgiveness then to get permission", All is well and some of my Holes are easier to get into!
Besides, the ice is getting thick and I can't be expected to provide dinner if I spend most of my fishing time and energy drilling holes!
I sure wish I could figure out how to post the photos of the nice trout I caught, made possible ofcourse, by the power auger!

[Big K]

"It is much easier to ask for forgiveness then to get permission"

I like that gamalot! I'm going to have to remember that one.

[TrailFndr]

The wife was really thrilled with me! While at the shop getting new blades for the laser, I found this neat little gadget called a Strikemaster Mag 2000. $300 later I was a star at home!
In keeping with the motto by which I live, "It is much easier to ask for forgiveness then to get permission", All is well and some of my Holes are easier to get into! Besides, the ice is getting thick and I can't be expected to provide dinner if I spend most of my fishing time and energy drilling holes!

From MRS. TRAILFNDR.....

"PLEASE!! don’t give my husband any ideas!!!!!!!!
I know you had good intentions, letting all the guys know that asking forgiveness was easier than getting permission, but remember…lakes have been known to have a NO ACCESS sign posted, making the holes inaccessible."

[carp_assasin]

lakes have been known to have a NO ACCESS sign posted, making the holes inaccessible.

In my house leg's have been known to have NO ACCESS signs posted, when I pull something like that!

[gamalot]

Dear Mrs. Trailfinder;
Far be it from me to give the real trail finder any new paths!
I have been to that lake with POLE in hand and have learned, when it freezes over, thats where it stays!
Fortunately, I have also learned to buy her flowers and cook her a nice meal. I think I forgot the other part of this one but a bit of immagination should work.

[Kevin]

Paul,
1. Why a piece of glass? Just because of the flat surface? Requires that one not apply too much pressure?
2. My auger blade is actually convex; along the arc of the curved metal to which it is attached. Does a flat tool still make sense, or should I fashion a similarly curved block to attach the abrasive to?
3. Any reply to Dave W.'s Dremel question? It would be faster for me too I think.
Thanks pal,
Kevin